cavity wall

英 [ˌkævəti ˈwɔːl]

美 [ˌkævəti ˈwɔːl]

n.  (有保暖作用的)空心墙，夹壁墙

医学

牛津词典

noun

• （有保暖作用的）空心墙，夹壁墙
  a wall consisting of two walls with a space between them, designed to prevent heat from escaping
  1. cavity wall insulation
     空心墙隔热

柯林斯词典

• N-COUNT (隔音或防寒的)空心墙，夹层墙
  Acavity wallis a wall that consists of two separate walls with a space between them. Cavity walls help to keep out noise and cold.
  1. ...cavity wall insulation.
     空心墙隔音材料

英英释义

noun

• a wall formed of two thicknesses of masonry with a space between them

双语例句

• A ( test): after being eroded through acid, the cavity wall was spread with EM dental adhesive, then filled with silver amalgam.
  A组：经酸蚀后在洞壁周围涂以薄层EM粘结剂，吹匀随即以银汞合金充填。
• Insulate your home. Cavity wall insulation can cut heat loss through the wall by up to 60 percent.
  房屋隔热可以利用空心墙来减少热能损耗，降幅高达60%。
• Conclusion Bonding resin could distinctly reduce microleakage and assure good adaptation between the cavity wall and amalgam.
  结论应用树脂粘结剂可增加充填体与洞壁密合度，明显减少银汞合金充填微渗漏。
• Testing and Nonlinear Finite Element Analysis on Cavity Wall Structure
  空斗墙砌体结构检测与非线性有限元动力分析
• During the shore period of observation, carcinoma node, dimension of the cavity, thickness of the cavity wall and volume of liquid in the cavity have dynamic changes.
  囊腔内壁有附壁“结节影”（癌结），腔内有液体，在短期观察中“癌结”、“囊腔大小”、“囊壁的厚度”和“腔内液量”均有动态变化。
• Fuzzy optimal design facing cavity wall thickness of large-scale die casting mold
  面向大型压铸模型腔壁厚的模糊优化设计
• At last, a formula of the row-lock cavity wall strengthened with HPFL is presented to predicting the carrying capacity of seismic shear. The formula coincides well with the experimental results, can be used in practice projects.
  最后，本文提出了经HPFL条带加固空斗墙的抗剪承载力的计算公式，公式计算结果与试验结果吻合良好，可供加固设计人员在实际工程中参考使用。
• The three main problems faced by water pump are leakage, vibration noise and corrosion of the impeller and water cavity wall.
  汽车水泵的三个主要故障是泄漏、振动噪声和叶轮或水腔内的腐蚀。
• After entering the chamber, because of edge effects by the cavity wall, the flow rate of blank uneven, showing a distinct layered flow.
  在进入腔体以后，因边部受到腔体壁的影响，坯料的流动速率不均匀，可见明显的分层流动。
• Aiming at the injection mold structures of female mold on stationary mold, the force on the famale mold and male mold are analysed, and the cavity wall thickness are calculated.
  针对凹模安装在定模上、凸模安装在动模上的注塑模结构，对矩形型腔模具进行了受力分析和型腔壁厚计算。